VZT MontérHVAC ductwork calculator

App for iPhone and Android

Duct offsets, elbow patterns and airflow, worked out on site

VZT Montér is a calculator for ductwork installers. Put in what you measured with the tape and get the fit piece length, a 1:1 sheet metal template or the pressure loss of a duct run. Works offline, no account.

Download on the App Store Get it on Google Play

Free to download. PRO is a one-time purchase, no subscription.

VZT Montér app: planar offset Ø200, offset 500 mm, 45° elbows, fit piece length 541 mm

Ductwork calculators online

Four calculations from the VZT Montér app, free in your browser and using the same formulas as the app. Sizes in millimetres, airflow in m³/h.

Duct offset calculator

Fit piece length between two elbows for an offset in round (spiral) duct in one plane. Enter the diameter, the offset as the distance between the duct centrelines and the elbow angle.

O L α A
  • Fit piece length L541 mm
  • Diagonal length C707 mm
  • Axial run A500 mm
  • Elbow leg83 mm
  • Elbow radius R200 mm
How it is calculated

C = O / sin α, A = O / tan α, elbow leg R · tan(α/2) and fit piece L = C - 2 · R · tan(α/2). The elbow radius R is a multiple of the diameter, depending on the elbow type. Catalogue elbows often have a straight spigot after the bend, so check the leg on the elbow you actually have. If L comes out negative the elbows would overlap: a smaller angle helps.

Rolling offsets and offsets around obstaclesThe app also works out rolling offsets, offsets around an obstacle and rectangular duct offsets, and saves the result to a job.

App StoreGoogle Play

Duct velocity calculator

Air velocity from airflow and duct size, the cross-section area and the friction pressure loss per metre. For round spiral duct and rectangular duct.

Duct shape
  • Velocity v3.56 m/s
  • Cross-section S0.0779 m²
  • Friction loss0.49 Pa/m
How it is calculated

v = Q / (3600 · S). Friction loss by Darcy-Weisbach with the Swamee-Jain friction factor, air density 1.2 kg/m³, viscosity 15.11 · 10⁻⁶ m²/s, roughness 0.09 mm for spiral duct and 0.15 mm for galvanised rectangular duct. Rectangular duct uses the hydraulic diameter 2ab / (a + b) and the actual velocity.

The whole run, fittings includedThe app sizes every section of a run with branches, adds up the pressure loss with fittings, finds the critical path and sizes the fan.

App StoreGoogle Play

Rectangular to round duct conversion

Which round diameter has the same pressure loss at the same airflow as an a × b rectangular duct, and the nearest spiral duct sizes.

  • Equivalent diameter304.7 mm
  • Nearest spiral sizeØ300 / Ø315 mm
  • Same-area diameter319.2 mm
  • Duct area0.0800 m²
How it is calculated

Huebscher equation: D = 1.30 · (a · b)^0.625 / (a + b)^0.25. The same-area diameter is only for comparison, pressure loss follows the equivalent diameter. Spiral sizes: 63 to 1250 mm, including 180, 224 and 280 mm.

Both ways, with the standard seriesIn the app you can also convert a diameter to duct sizes for a chosen aspect ratio, find the nearest EN 1505 size and compare a replacement cross-section.

App StoreGoogle Play

Segmented elbow: cut angle and segment lengths

Gored elbow from spiral duct: the angle to set on the saw and the length of the full and half segments. The segment count includes the two half segments at the ends.

  • Saw cut angle15.00°
  • Bend at each joint30.00°
  • Elbow make-up2 full + 2 halves
  • Full segment on centreline161 mm
  • Full segment, inside107 mm
  • Full segment, outside214 mm
  • Half segment on centreline80 mm
  • Half segment, inside54 mm
  • Half segment, outside107 mm
How it is calculated

Cut angle from square α = Θ / (2 · (n - 1)), where n counts all pieces. Full segment on the centreline 2 · R · tan α, inside 2 · (R - D/2) · tan α, outside 2 · (R + D/2) · tan α. Half segments are half as long with one square end. The bend at each joint (2α) is not the saw angle.

1:1 PDF patternThe app prints the segment pattern as a 1:1 template on A4 sheets with a 100 mm check line. The same for miter cuts, branches, round-to-rectangular transitions and cone reducers.

App StoreGoogle Play

What VZT Montér does

Everything runs on the phone, offline and without an account. Save calculations to the history or to a job.

Offsets Free PRO

Planar offsets on spiral duct and rectangular duct offsets for radiused, mitred and vaned mitred elbows are free. Rolling offsets, offsets around an obstacle and custom elbow angles with PRO.

Cutting and development PRO

Miter cut, segmented elbow, branch (saddle), round-to-rectangular transition and cone reducer. Cut points in a table in whole mm and a 1:1 PDF template on A4 sheets with a 100 mm check line.

Conversions Free

Round to rectangular, airflow, velocity and diameter, nearest spiral and EN 1505 size, room airflow requirement and cross-section replacement.

Route design and losses PRO

Sections with branches, sizing, pressure loss, critical path, throttling at each outlet, fan sizing and a material takeoff.

Quick section check PRO

One section, instant result: friction and fittings, fan, dew point and condensation risk.

Jobs, quotes and work log Free PRO

Calculations saved to a job with a PDF report, and a work log with the month's earnings. Free for 3 jobs and 14 days of the log. Unlimited with PRO, plus site photos, a PDF hours report and quotes from your price list.

Tables Free

Spiral and rectangular duct series, local loss coefficients, roughness values, elbow radii and recommended velocities.

Built for site work

Day mode is black and white so you can read it in the sun, night mode is for the plant room. Big buttons for gloves. English, Czech, Slovak, German and Polish.

What the app looks like

Free and PRO

Free

The basics for every job

  • Planar offset and rectangular duct offset
  • Conversions and tables
  • Calculation history
  • 3 jobs
  • Work log for 14 days
  • Backup to a file

VZT Montér PRO

One-time purchase

  • Rolling offset, offset around an obstacle, custom angle
  • Cutting and development with 1:1 templates
  • Route design, pressure loss and fan sizing
  • Unlimited jobs, quotes and PDFs without a watermark
  • Unlimited work log, photos and PDF hours report

Pay once, nothing renews. The store shows the price in your currency.

FAQ

How is the fit piece of a duct offset calculated?

The offset O and the elbow angle α give the diagonal C = O / sin α. Subtract two elbow legs R · tan(α/2). For example Ø200 mm, a 500 mm offset and 45° elbows with the standard 1.0×D radius give a 541 mm fit piece.

Does the app work offline?

Yes. Calculations, jobs and the work log run on the phone. A connection is only needed to buy or restore PRO.

Is PRO a subscription?

No. PRO is a one-time purchase that never expires. Restore it on a new phone in Settings.

Where is my data?

Only on your phone, no account needed. Save a backup file and move it wherever you like. Details are in the privacy policy.

Which phones and languages?

iPhone and Android phones. The app is in English, Czech, Slovak, German and Polish.

The result does not match the job. What now?

Write to info@deriverge.com with your inputs and the result you got. We will check the calculation. More answers in Support.

Get VZT Montér

Free for iPhone and Android. PRO as a one-time purchase, no subscription.

Download on the App Store Get it on Google Play